GSA 8 Release Notes
Contents
- GSA Restrictions
- GSA (not yet published)
- GSA 8.7 build 80 (released 5 September 2017)
- GSA 8.7 build 79 (released 30 June 2017)
- GSA 8.7 build 78 (released 4 May 2017)
- GSA 8.7 build 77 (released 20 March 2017)
- GSA 8.7 build 74 (released 17 January 2017)
- GSA 8.7 build 73 (released 11 November 2016)
- GSA 8.7 build 72 (released 29 September 2016)
- GSA 8.7 build 70 (released 2 September 2016)
- GSA 8.7 build 68 (released 29 June 2016)
- GSA 8.7 build 67 (released 3 June 2016)
- GSA 8.7 build 66 (released 8 April 2016)
- GSA 8.7 build 62 (released 15 December 2015)
- GSA 8.7 build 60 (released 4 December 2015)
- GSA 8.7 build 59 (released 3 December 2015)
- GSA 8.7 build 57 (released 5 November 2015)
- GSA 8.7 build 54 (released 21 October 2015)
- GSA 8.7 build 53 (released 6 October 2015)
- GSA 8.7 build 52 (released 28 September 2015)
- GSA 8.7 build 50 (released 9 September 2015)
- GSA 8.7 build 49 (released 29 July 2015)
- GSA 8.7 build 45 (released 27 May 2015)
- GSA 8.7 build 43 (released 5 March 2015)
- GSA 8.7 build 42 (released 12 February 2015)
- GSA 8.7 build 41 (released 6 February 2015)
- GSA 8.7 build 37 (released 17 December 2014)
- GSA 8.7 build 36 (released 21 November 2014)
- GSA 8.7 build 33 (released 13 October 2014)
- GSA 8.7 build 31 (released 7 August 2014)
- GSA 8.7 build 28 (released 23 June 2014)
- GSA 8.7 build 27 (released 17 June 2014)
- GSA 8.7 build 22 (released 14 May 2014)
- GSA 8.7 build 21 (released 17 April 2014)
- GSA 8.7 build 19 (released 1 April 2014)
- GSA 8.7 build 16 (released 12 March 2014)
- GSA 8.7 (first released 14 February 2014)
- GSA 8.6 sp 1 build 23 (released 26 November 2012)
- GSA 8.6 sp 1 build 20 (released 28 September 2012)
- GSA 8.6 sp 1 build 18 (released 11 July 2012)
- GSA 8.6 sp 1 build 15 (released 27 June 2012)
- GSA 8.6 build 9 (released 13 March 2012)
- GSA 8.6 (first released 10 February 2012)
- GSA 8.5 sp 1 build 27 (released 27 September 2011)
- GSA 8.5 sp 1 build 24 (released 24 June 2011)
- GSA 8.5 sp 1 build 21 (released 18 April 2011)
- GSA 8.5 sp 1 build 20 (released 15 April 2011)
- GSA 8.5 sp 1 build 19 (released 18 March 2011)
- GSA 8.5 build 14 (released 21 December 2010)
- GSA 8.5 build 10 (released 30 September 2010)
- GSA 8.5 build 8 (released 18 August 2010)
- GSA 8.5 (first released 3 August 2010)
- GSA 8.4 build 20 (released 1 July 2010)
- GSA 8.4 build 19 (released 17 May 2010)
- GSA 8.4 build 17 (released 14 December 2009)
- GSA 8.4 build 15 (released 26 October 2009)
- GSA 8.4 build 11 (released 28 September 2009)
- GSA 8.4 (first released 14 September 2009)
- GSA 8.3 (first released 24 June 2008)
- GSA 8.2 latest patches
- GSA 8.2 build 3 (released 25 July 2007)
- GSA 8.2 build 2 (released 13 February 2007)
- GSA 8.2 build 1 (released 20 December 2006)
- GSA 8.1 latest patches
- GSA 8.1 build 12 (released 22 December 2005)
- GSA 8.1 build 9 (released 4 November 2005)
- GSA 8.1 build 7 (released 14 October 2005)
- GSA 8.1 build 4 (released 10 August 2005)
- GSA 8.1 build 3 (released 29 July 2005 as a patch)
- GSA 8.1 (released 1 July 2005)
- GSA 8.0 build 34 (released 21 April 2005)
- GSA 8.0 build 30 (released 7 May 2004)
- GSA 8.0 build 27 (released 12 December 2003)
- GSA 8.0 build 15 (released 14 February 2003)
- GSA 8.0 build 9 (released 5 November 2002)
- GSA 8.0 initial release (released 5 September 2002)
- GSA Outstanding Bugs
GSA restrictions
GSA restrictions — Gss Solver
- Link element forces and reactions at nodes on link elements can be wrong when the link elements are connected in a chain.
GSA restrictions — GsRelax Solver
- Element offsets cannot be analysed by GsRelax.
- If the constraint axes of the two nodes of a joint differ the model cannot be analysed by GsRelax.
- Distortion loads not acting at the end of a beam or not in the x, y or z direction cannot be analysed by GsRelax.
- Fablon uses 4 triangular elements to simulate a Quad 4 element in the analysis in which a dummy node at the centre of the Quad 4 element is introduced. The results at the 4 nodes are the average of the results of the two adjacent triangular elements and the results at the centre is the average of the 4 triangle elements. It is expected that the results are not consistent with true 4-noded quad element.
- In the post-processing of 1D element results, the original length rather than the deformed length is used in the calculation of beam shear forces and moments. If an element is loaded and its deformed length is significantly different to its original length (and the results are from a GsRelax analysis), the output of beam shear forces and moments may not be correct.
GSA restrictions — Interface
- When running Remote Desktop on a Windows 7 machine to access another machine (whether running Windows 7 or XP) to run GSA, the performance of Graphic Views is degraded in that rubber-banding leaves a trail, selection marks do not 'stick' and legend text is badly formatted.
GSA Recent New Features (not yet published)
None implemented since the last release.
GSA Recent Fixes (not yet published)
Items identified as 'released' in this section are available as a revised component, by request from Oasys. They will be built into an updated installation in due course.
GSA recent fixes — Design
- The value of fcdc for EN1992 code is incorrect. The value should be multiplied by 0.52.
[NCR11360] (Fixed 14 September 2017)
GSA recent fixes — Analysis
- When creating response spectrum for China design codes GB50011-2001 & 50011-2010, all parameters are zero.
[NCR11415] (Fixed 18 December 2017)
GSA 8.7.0.80 - New Features
- The relative displacement option for response spectrum analysis now includes rotations as well as translations.
GSA 8.7.0.80 - Fixes
GSA 8.7.0.80 - Fixes — General
- When grid loading is used and only selected results are required the expanded beam loads get deleted when the analysis completes resulting in incorrect results along elements.
[NCR11310] (Fixed 24 July 2017) - The ‘Reset Grid/Face Loading’ command will not clear face loads expanded for load panel elements when there are no grid planes or grid loads in the model.
[NCR11312] (Fixed 26 July 2017)
GSA Recent Fixes — Analysis
- Nonlinear analysis does not converge if nodes in a rigid constraint belong to the current analysis stage do not connect to any active elements
[NCR11319] (Fixed 31 July 2017) - If 2D element in-plane thickness is modified, the buckling analysis and p-delta analysis results are incorrect
[NCR11333] (Fixed 14 August 2017)
GSA Recent Fixes — Design
- In RC Slab if user dedfined reinforcements are specified, reinforcement areas cannot be calculated.
[NCR11336] (Fixed 18 August 2017)
GSA 8.7.0.79 - New Features
GSA 8.7.0.79 - New Features — General
- The output axes are now reported in the Report tab of the Object Viewer. Also if 'displayed results' is selected the output axes are set to the output axes of the displayed results.
GSA 8.7.0.79 - Fixes
GSA 8.7.0.79 - Fixes — General
- GSA refuses to read view settings from a .gwb file if the model sets contain a critical sequence of entity numbers.
[NCR11268] (Fixed 6 June 2017) - GSA crashes if a combination case is input whose descrption refers to an analysis task that does not exist.
[NCR11286] (Fixed 29 June 2017)
GSA 8.7.0.79 - Fixes — Analysis
- GSA crashes when doing p-delta analysis and p-delta modal buckling analysis with combination case as p-delta case, the workaround is to use equivalent analysis as p-delta case.
[NCR11249] (Fixed 22 May 2017) - GSA crashes trying to run footfall analysis if no response nodes have been set.
[NCR11260] (Fixed 31 May 2017) - Tool for generating "Spectrum Scaling factors of modes" does not work if user defined spectrum is used.
[NCR11273] (Fixed 14 June 2017) - Beam translational releases do not work correctly in nonlinear analysis if displacements are large.
[NCR11274] (Fixed 14 June 2017)
GSA 8.7.0.79 - Fixes — Design
- HK steel design: While checking buckling interaction, the steel checker incorrectly uses the plastic section capacity instead of the elastic section capacity when the section is plastic.
[NCR11235] (Fixed 9 May 2017)
GSA 8.7.0.79 - Fixes — Table Views
- 2D Element Loading Thermal: Editing the last row via wizard could crash GSA.
[NCR11289] (Fixed 16 June 2017)
GSA 8.7.0.78 - New Features
GSA 8.7.0.78 - New Features — Interface with Third Party Software
- The GSA-Revit link is now compatible with Revit 2018.
GSA 8.7.0.78 - Fixes
GSA 8.7.0.78 - Fixes — General
- When using load panels to distribute load the reference edge can get lost resulting in the load being attributed to the wrong edges.
[NCR11208] (Fixed 29 March 2017)
GSA 8.7.0.78 - Fixes — Analysis
- The calculation of modal damping from material damping is incorrect when the model contains elements with releases.
[NCR11205] (Fixed 27 March 2017) - GSA crashes trying to analyse in GSS where there are links in the model that refer to non-existent nodes.
[NCR11212] (Fixed 31 March 2017) - GSA crashes analysing a small number of models containing load panels.
[NCR11215] (Fixed 3 April 2017) - GSA crashes setting up dynamic, P-delta, Ritz and model stability analysis when there are combination cases in the model that refer to non-existent combinations.
[NCR11216] (Fixed 4 April 2017)
GSA 8.7.0.78 - Fixes — Design
- When the required reinforcement areas are very small, sometimes RC slab design fails to calculate the reinforcement areas and wrongly shows impossible to calculate the reinforcement areas.
[NCR11214] (Fixed 27 March 2017) - When extra eccentrcity has been defined in RC slab property, the calculated reinforcement areas may not be correct.
[NCR11223] (Fixed 20 April 2017)
GSA 8.7.0.77 - New Features
GSA 8.7.0.77 - New Features — Analysis
- Footfall analysis using AISC SDG11 (Vibrations of Steel-Framed Structural Systems Due to Human Activity) 2nd edition for walking on floor, walking on stair and running on floor.
- Load panel elements can now be bounded by zero length link elements as well as beam/bar elements. This allows for modified ‘releases’ to be set in different stages. No load is applied to the link elements. An additional check is made for load panels that are bounded by coincident elements.
GSA 8.7.0.77 - New Features — Design
- In RC slab design, a new parameter (user defined additional eccentricity) is added to RC slab property, this will allow users to explicitly define this additional eccentricity to consider the slenderness effect of the RC slab/wall when in-plane forces are significant.
GSA 8.7.0.77 - Fixes
GSA 8.7.0.77 - Fixes — General
- GSA crashes when running 'Create Patterned Loads' from Tools menu if element list of beam loads is empty. The workaround is to delete this beam load or add element to the element list.
[NCR11116] (Fixed 19 January 2017) - When pasting explicit postions into the assemblies table the units can get lost resulting in the values being interpreted as SI.
[NCR11121] (Fixed 30 January 2017) - Some of the total forces/moments are not written to gwa files.
[NCR11155] (Fixed 1 March 2017) - When reading text files, GSA garbles combination cases with envelopes of combinations that are later in the file.
[NCR11179] (Fixed 10 March 2017) - When reading gwa files some items can get a 'version' number added to the name. Ths affects Grid Planes, Grid Lines and Polylines.
[NCR11181] (Fixed 13 March 2017) - When reading section (PROP_SEC) records from gwa files the section formation type is ignored.
[NCR11193] (Fixed 17 March 2017)
GSA 8.7.0.77 - Fixes — Analysis
- When node loads are applied to nodes that are inactive in the solution, these loads are still included in the total loads and in the ignored node list. This does not affect the rest of the analysis. This is now modified so that these loads are ignored.
[NCR11128] (Fixed 6 February 2017) - Creep factor defined in stage definition is missed out for thermal load in linear (GSS) analysis.
[NCR11129] (Fixed 6 February 2017) - Creep factor defined in stage definition is missed out in nonlinear (GsRelax) analysis .
[NCR11130] (Fixed 6 February 2017) - If beam element has axial release and the release end is connected to a Link element, the link element forces and moments will not be available from nonlinear analysis.
[NCR11145] (Fixed 23 February 2017)
GSA 8.7.0.77 - Fixes — Design
- EC3 steel design: EC3 steel design grade S450 (EN) name is shown incorrectly as S460 (EN).
[NCR11176] (Fixed 9 March 2017) - EC3 steel design: The steel checker incorrectly uses the yield strength when selecting a buckling curve. This sometimes gives a conservative estimate of buckling capacity for S460 steel grade.
[NCR11187] (Fixed 15 March 2017) - When a load design code is set in the new model wizard, the selected code is ignored and reset to Undefined.
[NCR11192] (Fixed 16 March 2017)
GSA 8.7.0.77 - Fixes — Interface with Third Party Software
- GsRevit: Orientation of framing members (beams and braces) is not imported into Revit 2016/2017.
[NCR11120] (Fixed 24 January 2017) (Released in GsRevit_R16/R17 8.7.0.75)
GSA 8.7.0.74 - New Features
GSA 8.7.0.74 - New Features — Analysis
- The 'projected proportional' leg length type has been added to the Spacer Properties. After form-finding analysis this results in the final projected leg length of spacer elements being proportional to the original projected leg length.
GSA 8.7.0.74 - New Features — Design
- Steel design to CSA S16-14 has been implemented.
GSA 8.7.0.74 - Fixes
GSA 8.7.0.74 - Fixes — General
- Dummy beam elements on load panel edges cause an error when expanding face loading.
[NCR11109] (Fixed 6 January 2017)
GSA 8.7.0.74 - Fixes — Analysis
- The use of a damping table in response spectrum analysis was inconsistent with its use in the other dynamic response options. Rather that use the values only for the specified modes, the values for unspecified modes were calculated by interpolation from the table, rather than using the user specifed constant value.
[NCR11098] (Fixed 19 December 2016) - GSA crashes in data checks or when trying to analyse a model with wall elements that refer to nodes that do not exist.
[NCR11107] (Fixed 5 January 2017)
GSA 8.7.0.74 - Fixes — Design
- Steel design: The steel checker incorrectly uses the yield strength of the ASTM A36 material as 35 ksi.
[NCR11067] (Fixed 16 November 2016) - Steel design: The 'Steel Design Calcs (verbose)' output omits the member number from the output.
[NCR11094] (Fixed 14 December 2016) - EC3 steel design: The steel checker sometimes incorrectly estimates the modification factor for the reduction factor for lateral torsional bending.
[NCR11096] (Fixed 15 December 2016) - RC slab design: If reinforcement cover is small compared with slab thickness, RC slab design may fail to produce reinforcement areas.
[NCR11101] (Fixed 22 December 2016) - Canadian steel design (CSA S16): When checking sections heavier than 313 kg/m of ASTM A36 steel in the buckling compression capacity check the steel checker now sets the 'n' factor to 0.93.
[NCR11105] (Fixed 4 January 2017) - Steel design: The tolerance for the end moments used when checking for bending moment reversal in lateral torsional buckling calculations has been increased.
[NCR11106] (Fixed 4 January 2017)
GSA 8.7.0.74 - Fixes — Table Views
- When pasting a column into Table View entries in other columns are sometimes reset.
[NCR11047] (Fixed 14 November 2016) (Partial fix released in GSA 8.7 build 73)
GSA 8.7.0.74 - Fixes — Interface with Third Party Software
- When exporting a NASTRAN file GSA build an index of materials used, but omitted 2D elements when creating the index, leading to materials missing in the NASTRAN file.
[NCR11068] (Fixed 16 November 2016)
GSA 8.7.0.73 - New Features
None.
GSA 8.7.0.73 - Fixes
GSA 8.7.0.73 - Fixes — General
- GSA crashes opening the steel restraint properties table when there are gaps in the property numbers.
[NCR11033] (Fixed 12 October 2016) - GSA does not save the characteristic period and horizontal seismic influence coefficient of the response spectrum for GB 50011-2001 and GB 50011-2010 design codes.
[NCR11041] (Fixed 24 October 2016)
GSA 8.7.0.73 - Fixes — Analysis
- If 1D elements are included in the element list for defining 2D element pre-stress loads, GSA crashes. The workaround is to remove 1D elements from the list or to define dummy 2D element properties with the same property number that have been referred to by the 1D elements.
[NCR11040] (Fixed 25 October 2016) - GSA hangs if you try to analyse a model that has elements linking coincident nodes that lie in grid planes.
[NCR11053] (Fixed 7 November 2016)
GSA 8.7.0.73 - Fixes — Graphic Views
- Contour colours are inverted when drawn over sections and a dark background.
[NCR11042] (Fixed 25 October 2016)
GSA 8.7.0.73 - Fixes — Design
- RC slab sometimes fails to calculate required reinforcement areas even though valid areas are available.
[NCR11052] (Fixed 4 November 2016)
GSA 8.7.0.73 - Fixes — Table Views
- Table View crashes occasionally in Undo operations.
[NCR11048] (Fixed 11 November 2016)
GSA 8.7.0.72 - New Features
None.
GSA 8.7.0.72 - Fixes
GSA 8.7.0.72 - Fixes — General
- When any lists, axes, materials or properties in a model have names that are more than 250 characters long, GSA crashes editing tables that refer to these modules.
[NCR11007] (Fixed 8 September 2016) - Typing = in tables changes other fields in the same record, not just the current field.
[NCR11021] (Fixed 27 September 2016)
GSA 8.7.0.72 - Fixes — Design
- RC slab design: Maximum strain limit for reinforcement should be taken from relevant design code or user defined, but it is not the case at the moment. It is hard coded to 0.045, so it is wrong if code specified limit is not 0.045.
[NCR11008] (Fixed 14 September 2016) - RC slab design: Strength reduction factor (phi) is missed out in RC slab design for ACI codes.
[NCR11009] (Fixed 19 September 2016) - AISC Steel Checker: Steel checker is conservatively using a safety factor of 0.9 for hot rolled I sections under shear.
[NCR11014] (Fixed 26 September 2016)
GSA 8.7.0.72 - Fixes — Graphic Views
- The Connect 1D Elements sculpt command does not update the display list to include new entities.
[NCR11018] (Fixed 26 September 2016) - The Connect 1D Elements sculpt command sometimes skips element creation when connecting along a line of 2D elements.
[NCR11023] (Fixed 27 September 2016)
GSA 8.7.0.72 - Fixes — Interface with Third Party Software
- GsRevit: When exporting from Revit to GSA, section mappings defined in mappings.db3 are overridden by mappings defined in shared parameters.
[NCR11016] (Fixed 23 September 2016) (Released in GsRevit 8.7.0.71)
GSA 8.7.0.70 - New Features
None.
GSA 8.7.0.70 - Fixes
GSA 8.7.0.70 - Fixes — General
- GSA crashes reading models that contain explicit members that cannot be resolved into elements.
[NCR10945] (Fixed 7 July 2016) - A tied interface check reports an error when a tied interface references the same node on both sides of the interface.
[NCR10948] (Fixed 11 July 2016) (Released in GsCheck.dll 8.7.0.69) - The Equivalent Static / Accidental Torsion load generation does not work properly for loads generated from a respnse spectrum analysis.
[NCR10994] (Fixed 11 August 2016) - GSA can crash when manipulating data based on members where the member topology is ill-defined (e.g.topology items repeated).
[NCR10997] (Fixed 18 August 2016) - On Chinese language computers, GSA displays a garbled error message containing Chinese characters when there is a syntax error in combinations.
[NCR10999] (Fixed 19 August 2016) - When using the 'Create Members from Elements' command GSA is sometimes unable to form a single member from a string of beam elements when the model contains 2D elements.
[NCR11005] (Fixed 31 August 2016)
GSA 8.7.0.70 - Fixes — Analysis
- If influence line is constant (i.e. horizontal line), the worst load cases involving vehicle loads may be missed out in bridge load optimisation analysis.
[NCR10958] (Fixed 14 July 2016) - Settlement loads on the nodes of 2D elements with MITC formulations are applied incorrectly.
[NCR10965] (Fixed 19 July 2016) (Released in Gss.dll 8.7.0.69)
GSA 8.7.0.70 - Fixes — Design
- RC Slab design sometimes fails to produce reinforcement areas or gives extremely high reinforcement areas.
[NCR10990] (Fixed 8 August 2016)
GSA 8.7.0.70 - Fixes — Interface with Third Party Software
- GsRevit: When exporting Revit floor and wall entities to GSA with openings touching the boundary badly formed areas are created in the GSA model.
[NCR11006] (Fixed 23 August 2016)
GSA 8.7.0.68 - New Features
None.
GSA 8.7.0.68 - Fixes
GSA 8.7.0.68 - Fixes — General
- GSA reports intermediate results for models with grid loads or load panels wrongly if lists or geometry in the model are added or changed after analysing.
[NCR10925] (Fixed 20 June 2016)
GSA 8.7.0.68 - Fixes — Design
- Minimum reinforcement areas defined in RC slab property are sometimes ignored in RC slab design.
[NCR10911] (Fixed 13 June 2016)
GSA 8.7.0.68 - Fixes — Interface with Third Party Software
- GSA can crash when exporting a NASTRAN data file. This occurs when link elements are included in the model but the link element properties are not defined. Defining a link property will avoid the problem.
[NCR10898] (Fixed 8 June 2016) - GsRevit: When exporting Revit floor and wall entities to GSA as areas some are exported as overlapping areas.
[NCR10924] (Fixed 20 June 2016)
GSA 8.7.0.67 - New Features
GSA 8.7.0.67 - New Features — General
- There is now support for cloud-controlled network floating licensing. The advantage over the previous licensing is that network seats expire on the web server if not in use for a defined period of time.
GSA 8.7.0.67 - New Features — Graphic View — Sculpt
- The finding of existing nodes has been sped up in the following sculpt operations:
- Split 1D elements/lines
- Split Quad elements
- Split Tri elements
- Modify linear 2D to parabolic
- Snap
GSA 8.7.0.67 - New Features — Interface with Third Party Software
- The GSA-Revit link is now compatible with Revit 2017.
Note that the GsRevit executable has been digitally signed by Oasys Ltd to verify that it was published by Oasys. However the first time it is run Revit will ask you to confirm that you wish to run the executable.
GSA 8.7.0.67 - Fixes
GSA 8.7.0.67 - Fixes — General
- When a material name is set in the wizard it is not saved and is lost on exit.
[NCR10805] (Fixed 12 April 2016) - Spurious beam loads can be generated from grid area loads when the polygon defining the load and the polygon defining the panel on the structure have a single point in common.
[NCR10812] (Fixed 18 April 2016) - In some dialogs where the text should include Greek symbols, or superscript/subscript characters the text is blank.
[NCR10827] (Fixed 27 April 2016)
GSA 8.7.0.67 - Fixes — Analysis
- If there is a modal analysis task in front of static analysis task, Pseudo response spectrum analysis cannot be done.
[NCR10816] (Fixed 20 April 2016) - When expanding load panel loading on to beam elements with offsets the offsets are not properly accounted for if they are local relative to the element. This does not affect global offsets.
[NCR10817] (Fixed 21 April 2016) - If EC2 code and UK Annex is used, the uncracked concrete strength is overestimated in RC slab design, i.e. a 0.85 factor is missed out.
[NCR10828] (Fixed 28 April 2016) - If a model has very large beam sections and the analysis is for internal loads (thermo and pre-stress loads etc) only, nonlinear analysis results may be incorrect. The workaround is to use absolute residual instead of relative residual in the analysis
[NCR10841] (Fixed 9 May 2016) - If Link elements are forming a chain and the direction of the link elements is not from lower numbered link elements to higher numbered link elements, nonlinear analysis results may be wrong. The workaround is to make the direction of the link elements from lower numbered link elements to higher numbered link elemenmts
[NCR10847] (Fixed 12 May 2016)
GSA 8.7.0.67 - Fixes — Graphic Views
- Flipping a 1D element with local offsets gets the flipped offsets wrong.
[NCR10818] (Fixed 21 April 2016) - Some OpenGL functions were called without a valid context.
[NCR10843] (Fixed 10 May 2016)
GSA 8.7.0.66 - New Features
GSA 8.7.0.66 - New Features — General
- The sub-model extraction now has a couple of enhancements:
- Orientation nodes are no longer considered when establishing if a joint or rigid constraint crosses the boundary.
- There is an option to continue when a rigid constraint crosses the boundary. In this case the relevant nodes in the sub-model will be fixed and given settlements corresponding to the full-model displacements for these nodes. It is up to the engineer to determine of this is appropriate.(Released in GSA 8.7.0.64)
- When assemblies contain 2D elements the force calculation can be made from the element stresses, or the element forces and moments. Previously this calculation always used the stresses resulting in zero values if the stresses were not present. It is now modified to use the stresses if available, and if not to use the forces and moments.
(Released in GwDat.dll 50.12.0.65 & GsPrivate.dll 8.7.0.65)
GSA 8.7.0.66 - New Features — Graphic View — General
- Raft Interaction Areas are now labelled at their specified Elevation.
GSA 8.7.0.66 - New Features — Graphic View — Sculpt
- The Add String of 1D Elements command now offers the option to string to the next closest node.
(Released in GSA 8.7.0.64)
GSA 8.7.0.66 - New Features — Interface with Third Party Software
- GsRevit: Performance of the section mapping process has been improved by storing the result in GSA to avoid multiple COM calls.
(Released in GsRevit 8.7.0.64)
GSA 8.7.0.66 - New Features — Design
- RC slab design: The iteration routine for the optimum layer arrangement has been revised to speed up the process as well as to reduce the number of valid arrangements that are missed.
The change may result in small differences in the optimum reinforcement arrangement compared with previous versions, but both arrangements should be valid.
GSA 8.7.0.66 - Fixes
GSA 8.7.0.66 - Fixes — General
- Tied interfaces with node lists are not exported correctly to LS-DYNA.
[NCR10666] (Fixed 13 January 2016) (Released in GSA 8.7.0.64) - There is an additional option, enabled in the Miscellaneous preferences, to “use a block buffer” reading and writing files. You can try setting this option if you have trouble reading and writing large files.
[NCR10700] (Fixed 28 January 2016) - When elements included in an assembly are modified or split the element list in the assembly is not updated.
[NCR10731] (Fixed 18 February 2016) - When writing explicit members in GWA format the internal topology is not written if the member is invalid.
[NCR10764] (Fixed 7 March 2016) - Explicit members are treated as invalid when the group of the member and the corresponding elements are not the same.
[NCR10765] (Fixed 7 March 2016) - The calculation of polygon intersections can have problem with long, very thin polygons. This problem can manifest itself in a variety of ways, e.g. when displaying contours of grid loading where the load is spread across a number of intersection polygons.
[NCR10768] (Fixed 10 March 2016) - GSA crashes sculpting or manipulating models when there are dynamic response tasks with relative nodal displacements.
[NCR10782] (Fixed 21 March 2016) - Sculpting or manipulating nodes in large models takes a very long time.
[NCR10784] (Fixed 22 March 2016) - Element lists that include the syntax XYn (and similar) reference all elements.
[NCR10789] (Fixed 29 March 2016) - GSA throws an exception for 2D element result extraction via API output arrays.
[NCR10801] (Fixed 05 April 2016) - Force/moment components get muddled while extracting assembly results over the COM API.
[NCR10800] (Fixed 05 April 2016)
GSA 8.7.0.66 - Fixes — Analysis
- Form-finding analysis with 'X axis projected ratio' leg length type spacers does not work if the axis is not global.
[NCR10657] (Fixed 6 January 2016) (Released in GSA 8.7.0.63) - The pre-analysis data checks for tied interfaces could wrongly identify nodes as being on both the slave and master sides of the interface.
[NCR10660] (Fixed 7 January 2016) (Released in GSA 8.7.0.63) - GSA crashes when defining a 2D element offset in local axis directions.
[NCR10663] (Fixed 8 January 2016) (Released in GSA 8.7.0.63) - If a model has Tie or Strut elements or uses elastic-plastic material, grid loads and panel loads will be missed out in the second task of nonlinear analysis, therefore the second analysis results will be wrong if a model has grid loads or panel loads.
[NCR10665] (Fixed 12 January 2016) (Released in GSA 8.7.0.64) - If a model has wall elements, the modal damping is wrongly calculated as negative infinite from modal P-delta analysis.
[NCR10741] (Fixed 22 February 2016) - The modal damping (based on the material damping value) is not calculated when the dynamic analysis is carried out using the Ritz analysis option.
[NCR10744] (Fixed 24 February 2016) - If master and slave nodes in a rigid constraint are coincide, nonlinear analysis cannot proceed due to error in data checking.
[NCR10766] (Fixed 7 March 2016)
GSA 8.7.0.66 - Fixes — Design
- RC slab design sometimes fails to calculate the required reinforcement areas even though valid reinforcement areas should be available.
[NCR10743] (Fixed 23 February 2016) - EC3 Steel Checker: sometimes the Uniform Moment Factors and Interaction Factors are estimated incorrectly.
[NCR10802] (Fixed 8 April 2016)
GSA 8.7.0.66 - Fixes — Table Views
- In the Elements table the Dummy default field is ignored.
[NCR10654] (Fixed 5 January 2016) (Released in GSA 8.7.0.63)
GSA 8.7.0.66 - Fixes — Interface with Third Party Software
- GsRevit: Column orientation is imported into Revit incorrectly when the orientation angle in GSA is negative.
[NCR10689] (Fixed 25 January 2016) (Released in GsRevit 8.7.0.64) - GsRevit: If the Revit level height is not equal to the framing instance Z coordinate then the nearest Revit level is assigned to it and offsets are applied relative to the assigned level.
[NCR10745] (Fixed 24 February 2016) (Released in GsRevit 8.7.0.65)
GSA 8.7.0.62 - New Features
None.
GSA 8.7.0.62 - Fixes
GSA 8.7.0.62 - Fixes — General
- The fix [NCR10587] for panel expansion on adjacent load panels where there are element offsets on he beam elements, resulted in a problem when the elements had no offsets, leading to load terms being double counted. This problem did not exist in builds before GSA 8.7 build 59.
[NCR10624] (Fixed 11 December 2015) - The ‘Create Load Panels on Storeys‘ command crashes when there are gaps in the numbering of lists in the model.
[NCR10628] (Fixed 11 December 2015) - When using the tool to create load panels on a surface there can be instances where this fails. This is particularly the case with long thin panels.
[NCR10632] (Fixed 15 December 2015)
GSA 8.7.0.62 - Fixes — Design
- RC slab design sometimes fails to produce the required reinforcement areas where valid reinforcement should be available.
[NCR10636] (Fixed 14 December 2015)
GSA 8.7.0.62 - Fixes — Graphic Views
- The collection of entities that is to be displayed sometimes gets confused following a sculpt operation that adds entities.
[NCR10631] (Fixed 14 December 2015)
GSA 8.7.0.60 - New Features
None.
GSA 8.7.0.60 - Fixes
GSA 8.7.0.60 - Fixes — Analysis
- When going through analysis wizard for harmonic, time-history, periodic and footfall analysis, the modal analysis task ComboBox is not populated or populated with a wrong order of modal analysis tasks, so these dynamic response analyses cannot go ahead through the wizard..
[NCR10617] (Fixed 4 December 2015)
GSA 8.7.0.59 - New Features
GSA 8.7.0.59 - New Features — General
- The Wave Loading tool now allows wave loads to be generated for several wave profile data files in one go.
GSA 8.7.0.59 - New Features — Analysis
- Automatic bridge load optimisation analysis may now be carried out for Eurocode EC1_LM1.
GSA 8.7.0.59 - Fixes
GSA 8.7.0.59 - Fixes — General
- When face loads are applied to load panels and the surrounding beam elements have offsets, the loading on the offsets is incorrect when more than one face load contributes to the load on the beam.
[NCR10587] (Fixed 23 November 2015) - When calculating storey rotations the nodes close to the centre are subject to the largest rounding error and have a disproportionate effect on the resulting story rotation, leading to inaccurate rotation results in some cases. The algorithm has been changed to use a weighted average of the rotations calculated at the nodes to avoid this problem.
[NCR10593] (Fixed 25 November 2015) - It takes a very long time to create analysis envelopes when there are a large number of permutations in the combination.
[NCR10597] (Fixed 25 November 2015) - When an analysis stage is used to set creep factors these are considered in the analysis but not in the post-processing where intermediate displacements are calculated.
[NCR10601] (Fixed 27 November 2015) - The spectral accelerations for the Indian seismic code (IS 1893 (Part 1) : 2002 6.4.2) are too low by a factor of ‘g’.
[NCR10606] (Fixed 30 November 2015) - The tool for modal force calculation from a dynamic analysis is not working as the loadcase list is not interpreted correctly.
[NCR10610] (Fixed 1 December 2015)
GSA 8.7.0.59 - Fixes — Analysis
- Using "Pre-load" in advanced setting may make the relevant element forces/moments incorrect. As "pre-load" does not fit physical reality, this option is removed from GSA
[NCR10519] (Fixed 23 October 2015) - A combination of custom rigid constraints and settlements can cause GSA to crash.
[NCR10584] (Fixed 20 November 2015) - If working unit is not SI, the position of generated vehicle loads from bridge analysis are incorrect.
[NCR10599] (Fixed 27 November 2015) - If there are more than 9 member buckling analysis cases, drawing chart view for Member buckling analysis may not take the correct analysis case as selected.
[NCR10600] (Fixed 27 November 2015)
GSA 8.7.0.57 - New Features
GSA 8.7.0.57 - New Features — General
- There are times when it is necessary to refine a model by re-meshing from beam elements to shells. A new feature allows the loads on beam elements to be transferred to the new shell elements.
GSA 8.7.0.57 - Fixes
GSA 8.7.0.57 - Fixes — Analysis
- GSA sometimes crashes analysing models containing rigid constraints.
[NCR10546] (Fixed 4 November 2015)
GSA 8.7.0.57 - Fixes — Design
- EC3 Steel Checker: the Elastic Critical Moment is incorrectly computed for cantilever beams when using NCCI SN009a-EN-EU.
[NCR10542] (Fixed 3 November 2015)
GSA 8.7.0.57 - Fixes — Graphic Views
- When saving or printing saved views via COM held data scales revert to auto.
[NCR10532] (Fixed 30 October 2015)
GSA 8.7.0.54 - New Features
GSA 8.7.0.54 - New Features — General
- Assembly results are now reported as blank if the results are not available for any of the elements that form the assembly.
GSA 8.7.0.54 - Fixes
GSA 8.7.0.54 - Fixes — General
- When extracting a sub-model from GSA the orientation nodes on elements are not considered and these are then lost in the sub-model.
[NCR10506] (Fixed 20 October 2015)
GSA 8.7.0.54 - Fixes — Analysis
- Nonlinear analysis crashes if there are uniform thermal loads for shell elements, the workaround is to use equivalent initial strain loads to replace the thermal loads.
[NCR10478] (Fixed 7 October 2015) - Shell element centre only results are either not available or not correct from nonlinear analysis.
[NCR10480] (Fixed 7 October 2015) - Settlements were not included in the total loads and reactions leading to an apparant lack of equilibrium in the solution. Also settlements could be applied at constrained nodes leading to incorrect constraint and reaction forces. Settlements are now not allowed at constrained nodes.
[NCR10508] (Fixed 20 October 2015)
GSA 8.7.0.54 - Fixes — Design
- EC3 Fire Steel Checker: GSA unnecessarily carries out torsional buckling checks for hollow sections.
[NCR10502] (Fixed 20 October 2015) - EC3 Fire Steel Checker: GSA incorrectly computes the LT buckling utilization when moment reversal is present in the member.
[NCR10503] (Fixed 20 October 2015) - EC3 Steel Checker: GSA now uses Table B.1 for interaction factors when the LT buckling is ignored in accordance with clause 6.3.2.2 (4) of EN 1993-1-1:2005
[NCR10504] (Fixed 20 October 2015) - AS4100 Steel Checker: While calculating AlphaM for cantilever beams GSA ignores the lateral torsional restraint at free end.
[NCR10507] (Fixed 20 October 2015)
GSA 8.7.0.54 - Fixes — Graphic Views
- The deformed shape of beam elements when the section shape is displayed considers the intermediate rotations as zero.
[NCR10491] (Fixed 14 October 2015)
GSA 8.7.0.53 - New Features
GSA 8.7.0.53 - New Features — General
- The new 'pseudo response spectrum analysis' option has been introduced in the Analysis Wizard. This does the same basic calculation as a normal response spectrum analysis but the mode shapes are defined by static analysis cases and the engineer supplies the modal dynamic details (frequency, effective mass and modal mass) directly to the task.
- The new 'Tools | Manipulate Model | Extract Sub-model' option has been extended to work with analysis tasks associated with modal, Ritz and response spectrum analysis.
- Modal and Ritz analysis tasks are converted to and equivalent static analysis where a set of node loads are applied that correspond to the inertia load associated with the mode.
- Response spectrum analysis tasks are converted to pseudo response spectrum tasks and the dynamic details from the modal task are copied to the psuedo response spectrum task.
GSA 8.7.0.53 - Fixes
GSA 8.7.0.53 - Fixes — General
- When load panel elements are ill-defined (element refers to non-existent topology item) the load expansion will crash. Fixing the topology avoids the problem.
[NCR10463] (Fixed 1 October 2015)
GSA 8.7.0.53 - Fixes — Analysis
- Factored effects should be used to determine the critical load combinations in bridge load optimization analysis, but total effects are incorrectly used currently.
[NCR10464] (Fixed 2 October 2015)
GSA 8.7.0.52 - New Features
GSA 8.7.0.52 - New Features — General
- Internal calculations for assemblies now use ‘end points’ closer to he end of the assembly to reduce the rounding error in the extreme points.
(Released in GwDat.dll 50.12.0.51) - The new 'Tools | Manipulate Model | Extract Sub-model' option creates a new model from a specified element list. For selected static tasks settlements are applied to the boundary nodes representing the corresponding displacements.
GSA 8.7.0.52 - New Features — Analysis
- Link elements are now considered in response spectrum analysis.
(Released in GdSpec.dll 8.7.0.51)
GSA 8.7.0.52 - Fixes
None
GSA 8.7.0.50 - New Features
None.
GSA 8.7.0.50 - Fixes
GSA 8.7.0.50 - Fixes — General
- 'Import GWA' in 'overwrite' mode resets the model units to SI.
[NCR10393] (Fixed 7 August 2015) - Intermediate member user module values are sometimes not recognised for members that relate to several members.
[NCR10395] (Fixed 10 August 2015) - Grid loading can be wrongly calculated when the load polygon and the polygon formed by the panel touch at a single point. This can result in a doubling of the load being applied on the structure for this panel.
[NCR10404] (Fixed 18 August 2015) - Accidental torsion calculation not working when one of the storeys in the model has zero mass.
[NCR10418] (Fixed 1 September 2015) - Forces and moments for beam elements bounding load panels are not reported correctly after the model is saved and read back.
This bug does not affect results that have been produced by an analysis in the current session.
[NCR10424] (Fixed 3 September 2015)
GSA 8.7.0.50 - Fixes — Design
- EC3 Steel Checker: Checker ignores the applied moment direction while checking for Lateral Torsional Buckling. This effects unsymmetrical sections with negative moment.
[NCR10405] (Fixed 7 September 2015) - BS5950 Steel Checker: Checker sometimes incorrectly identifies 'strut connections' as 'member connections' for PFC section members.
[NCR10426] (Fixed 7 September 2015)
GSA 8.7.0.49 - New Features
GSA 8.7.0.49 - New Features — General
- Touch Gestures
Touch gestures are implemented as follows.- tap - click
- drag - drag
- pinch - zoom
- double finger drag - pan in Graphic Views [NEW]
- press and tap - right-click in Graphic Views [NEW]
GSA 8.7.0.49 - New Features — Output Options
- Resolved shear |Fyz|, and resolved moment |Myz| are now included in Beam and Spring Forces and Moments output and are available as contouring and diagram options.
GSA 8.7.0.49 - New Features — Graphic View — General
- Volumes now consider lines and areas independent of the regions to which they belong.
(Released in GsPrivate.dll 8.7.0.46)
GSA 8.7.0.49 - Fixes
GSA 8.7.0.49 - Fixes — General
- When using ‘Select by criteria’ to select by length, only 1D elements defined by a section are selected. This means links, cables and spring are ignored.
[NCR10295] (Fixed 1 June 2015) - Grid load expansion on one-way spanning grid planes can result in the generation of extra (incorrect) beam loading records. This problem always results in more load applied to the structure than specified.
[NCR10314] (Fixed 10 June 2015) (Released in GwDat.dll 50.12.0.46)
[NCR10321] (Fixed 11 June 2015) (Released in GwDat.dll 50.12.0.47) - Assembly definitions cannot be pasted into a model that has results.
[NCR10345] (Fixed 25 June 2015) - GSA crashes when any change that alters or deletes members is undone.
[NCR10349] (Fixed 26 June 2015) - Base shear calculations for seismic equivalent static analysis are incorrect.
[NCR10350] (Fixed 30 June 2015) (Released in Gsa.exe 8.7.0.47 and OaUtil.dll 50.12.0.47) - "Generate Static Vehicle Load..." tool fails to use model unit, SI unit is always used.
[NCR10360] (Fixed 7 July 2015) - GSA reports intermediate results for beams with grid loads or load panels wrongly after members are created or edited.
[NCR10378] (Fixed 20 July 2015) (Released in GwDat.dll 50.12.0.48) - GSA crashes analysing models with complex lists in them when a Graphic view is visible.
[NCR10385] (Fixed 28 July 2015)
GSA 8.7.0.49 - Fixes — Analysis
- If 1D elements are included in the element list in 2D element thermal load definition, Nonlinear analysis crashes.
[NCR10299] (Fixed 1 June 2015) - Footfall, harmonic, periodic and time history analyses cannot be done due to a wrong error message. The workaround is to define a response spectrum in the same file to enable the analysis to proceed.
[NCR10300] (Fixed 1 June 2015) - When calculating modal damping from material damping the elements with zero damping are ignored. This can lead to higher than expected damping values. Specifying a small (~0) damping value will avoid this problem.
[NCR10304] (Fixed 4 June 2015) - When centre-only values on 2D elements are specified for a response spectrum analysis, this option is ignored and values are calculated for all points. If the centre-only values are specified for the modal analysis then the response spectrum analysis results will contain invalid values for all but the first topology item, which will contains the centre value. This results in black contours and blanks in the output views.
[NCR10326] (Fixed 16 June 2015) - The phenomenon is the same as NCR10326 above, but this bug is for harmonic and time history analysis.
[NCR10328] (Fixed 16 June 2015) - When relative tolerance is used in raft analysis, the actual tolerance is sometimes too small for the analysis to converge. This is due to that the smallest soil settlement is used in calculating the actual tolerance, by right, the largest soil settlement should be used.
[NCR10353] (Fixed 1 July 2015) - GSA sometimes crashes analysing models that have wall elements in them.
[NCR10355] (Fixed 4 July 2015) - Response spectrum calculations are incorrect for nodes restrained in local axes.
[NCR10370] (Fixed 23 July 2015) - If a model with wall elements and the wall elements use non-local axis, the analysis results are sometimes wrong.
[NCR10372] (Fixed 17 July 2015) - Total Moments are reported incorrectly for Modal Analysis and Response Spectrum Analysis when the output axis is specified as a user defined axis.
Total Moments are calculated incorrectly in Modal Analysis by including the force contribution with the wrong sign.
[NCR10382] (Fixed 27 July 2015) - For Response Spectrum analysis cases reporting the Total Reactions separately for each restraint type led to a confusing sum of reactions. Total Reactions are now reported as a sum only for Response Spectrum cases.
[NCR10383] (Fixed 27 July 2015) - Saving intermediate results when terminating nonlinear analysis does not work.
[NCR10384] (Fixed 28 July 2015)
GSA 8.7.0.49 - Fixes — Design
- EC3 Steel Checker: GSA crashes while contouring steel utilisations when the section shape is RHS, CHS, T and PFC and the member is subjected to high shear force.
[NCR10317] (Fixed 11 June 2015) (Released in GSA_DES_EC3_2005.dll 50.12.0.46)
GSA 8.7.0.49 - Fixes — Graphic Views
- The Delete Displayed Loading sculpt command does not work on All Loading diagrams for other than grid loading.
[NCR10374] (Fixed 17 July 2015)
GSA 8.7.0.45 - New Features
GSA 8.7.0.45 - New Features — General
- For the Chinese seismic code GB50011, the code based values of Tg and αmax defining the spectrum can be overridden with locally specified values.
- The GSA program icons have been updated.
- The new installer framework will not install over more recent versions.
GSA 8.7.0.45 - New Features — Output Options
- When 'Envelope 'Subject Component' only' is selected then Maxima and Minima records are reported only for the subject component.
GSA 8.7.0.45 - New Features — Interface with Third Party Software
- GsRevit: data can now be copied from and pasted to the mappings tables in CSV format and imported from and exported to CSV file.
- GsRevit export: lines along line loads and around area loads can now be exported to GSA as lines.
- Export to DYNA files now includes translational releases on beam elements (in addition to rotational ones).
- The GSA-Revit link is now compatible with Revit 2016.
GSA 8.7.0.45 - New Features — Analysis
- Improvement in the accuracy of shell elements in large displacement nonlinear analysis.
GSA 8.7.0.45 - Fixes
GSA 8.7.0.45 - Fixes — General
- Local axis offsets are not handled in the GWA format.
[NCR10170] (Fixed 23 March 2015) (Released in GsFile.dll 50.12.0.44) - The tool to expand element offsets is not handling the local option – all offsets assumed to be in global.
[NCR10191] (Fixed 7 April 2015) (Released in GSA.exe. 8.7.0.44) - When specifying grid lines from the New Model wizard the Grid Line Definition dialog does not use the units specified in the New Model wizard.
[NCR10207] (Fixed 14 April 2015) - GSA does not correctly report the C value for calculation of the torsional stress in the properties dialog.
[NCR10247] (Fixed 28 April 2015) - The coefficient of thermal expansion for ACI concrete is incorrect.
[NCR10260] (Fixed 6 May 2015) - The "Tools | Seismic Analysis | Storey Masses" option can give wrong (zero) masses for the storeys. The total values are correct. This problem does not occur with the Mass analysis.
[NCR10292] (Fixed 20 May 2015) - SPEC_ACCELERATION does not work over COM GwaCommand.
[NCR10233] (Fixed 23 Apr 2015)
GSA 8.7.0.45 - Fixes — Analysis
- If no spectrum has been specified for a response analysis, GSA crashes trying to analyse the model.
[NCR10151] (Fixed 9 March 2015) - when plotting resultant displacement, velocity and acceleration against time from time history, the resultant displacements, velocities and accelerations are wrong in the chart view.
[NCR10179] (Fixed 27 March 2015) - Grid line loads which start 'on' a panel edge can result in a failure of the load expansion. Adjusting (nudging) the start point can help alleviate the problem.
[NCR10190] (Fixed 7 April 2015) - The grid loading algorithm can fail in a couple of situations:
- For one-way spanning grid planes with area loads defined by polylines the load is applied by slicing the polyline. A ‘vertical step’ in the polyline means that the algorithm may fail to find the next and subsequent slices, meaning that some of the load is skipped.
- For two-way spanning panels with corner effects included edges which are almost straight can result in the algorithm failing to detect the corner properly resulting in infinite loads applied to some of the beam elements.[NCR10210] (Fixed 16 April 2015)
- Modal damping calculated from modal analysis is incorrect for models with wall elements.
[NCR10282] (Fixed 12 May 2015)
GSA 8.7.0.45 - Fixes — Design
- EC3 Steel Checker: The steel checker is sometimes unable to converge while finding the section web classification.
[NCR10241] (Fixed 28 April 2015) (Released in GSA_DES_EC3_2005.dll 50.12.0.44)
GSA 8.7.0.45 - Fixes — Output Views
- When assemblies are defined by ‘storey’ the output view reporting of the storey at a position along the assembly can be wrong if the first storey is before the start of the structure/assembly.
[NCR10223] (Fixed 21 April 2015) - Compression and tension only spring stiffness are wrongly shown as zero in spring property output view.
[NCR10261] (Fixed 6 May 2015)
GSA 8.7.0.45 - Fixes — Graphic Views
- The exclusive volume (Ctrl+drag) does not work properly for regions.
[NCR10177] (Fixed 26 March 2015) - 'startup' views saved in the design layer do not open in the design layer. Also, when a 'startup' view is an initial view then the 'startup' view is opened twice.
[NCR10251] (Fixed 30 April 2015) - When displaying load diagrams, where a point load is located at the end of a patch load the point load is incorrectly displayed at the start of the element.
[NCR10276] (Fixed 7 May 2015) - In the design layer, either one of the grid or the legend were displayed at one given time. If the grid was turned on, the legend text stopped appearing.
[NCR10315] (Fixed 10 June 2015)
GSA 8.7.0.45 - Fixes — Interface with Third Party Software
- GsRevit Export: material properties are exported with values set to zero.
[NCR10293] (Fixed 27 May 2015)
GSA 8.7.0.43 - New Features
GSA 8.7.0.43 - New Features — Interface with Third Party Software
- GsRevit: columns in the 'Section Mappings' table can now be resized.
GSA 8.7.0.43 - Fixes
GSA 8.7.0.43 - Fixes — General
- GSA can either crash or fail to open the Advanced Analysis Options from the Analysis Wizard. This can happen when elements are defined but their properties are missing.
[NCR10106] (Fixed 23 February 2015) - The assemblies can in some instances lose elements that are at the ends of the assembly. This is due to a tolerance issue when determining if elements are part of the assembly. The graphic view shows the elements GSA is including in the assembly.
[NCR10112] (Fixed 24 February 2015) - The positioning of the assembly does not always work. This happens when the assembly is offset in the x direction from the origin of the axis in which it is defined. Assemblies defined by topology are not affected by this problem.
[NCR10129] (Fixed 27 February 2015) - When outputting results for combination cases the check that the base analysis cases exists does not work properly – in particular the combination is assumed to have results if results exist for the first referenced analysis case. This can lead to unexpected problems including empty results tables or even crashes.
[NCR10130] (Fixed 27 February 2015) - Saving a GWA file containing Raft | Displacement Data causes GSA to crash.
[NCR10132] (Fixed 2 March 2015) - Kv is set to be the same as Kz for all rectangular, T, I and channel sections. This is wrong for sections that are wider than they are high, where it should equal Ky.
[NCR10134] (Fixed 2 March 2015)
GSA 8.7.0.43 - Fixes — Analysis
- If an element is released and the release node has settlement load applied, the settlement is missed out for the end of the element release node.
[NCR10117] (Fixed 24 February 2015)
GSA 8.7.0.43 - Fixes — Design
- SANS 10162 & CSA S16 Steel Checkers: Steel checkers are missing the flexural torsion buckling capacities in the buckling interaction checks.
[NCR10095] (Fixed 18 February 2015) - BS5950 Steel Checker: Steel checker does not consider the intermediate lateral restraints when estimating the effective length for lateral torsional spans of simple members.
[NCR10142] (Fixed 3 March 2015) - EC3 Steel Checker: When checking for moment capacity under combined bending and shear the steel checker now reduces the moment capacity only for the corresponding shear area.
[NCR10143] (Fixed 24 February 2015)
GSA 8.7.0.43 - Fixes — Graphic Views
- The deformed shape of members is sometimes drawn incorrectly.
[NCR10141] (Fixed 18 February 2015)
GSA 8.7.0.42 - New Features
GSA 8.7.0.42 - New Features — Analysis
- Allow dummy mass and dummy inertia to be modified exponentially by a given power in addition to be modified by a linear factor in nonlinear analysis, this may be useful when a model has large stiffness difference between elements.
GSA 8.7.0.42 - Fixes
GSA 8.7.0.42 - Fixes — General
- User module values at the centre of 2D elements are not reported unless values at each nodal position have also been supplied.
[NCR10050] (Fixed 10 February 2015) - In the Contour Settings dialog when a Steel Utilisation data option is selected, selecting an Effective Length Factors data option crashes GSA.
[NCR10052] (Fixed 11 February 2015) - The Rationalize Lines command uses fixed tolerances that give the wrong results for some models.
[NCR10057] (Fixed 11 February 2015)
GSA 8.7.0.42 - Fixes — Design
- Contouring of Effective Length Factors for lateral torsional buckling to Eurocode 3 is incorrect.
[NCR10053] (Fixed 9 February 2015) - GSA hangs when displaying Effective Length Factors contouring if the result case includes permutations.
[NCR10054] (Fixed 10 February 2015)
GSA 8.7.0.41 - New Features
GSA 8.7.0.41 - New Features — General
- Element and member offsets at end nodes and internal nodes of explicit members are now ignored when considering the relationships between elements and members.
(Released in GwDat.dll 50.12.0.39) - The 'Select by criteria' tool now works for nodes (in addition to elements and members). Options for criteria include nodal coordinates, colour, being active in an analysis case, being part of a list, restraints and support stiffnesses.
GSA 8.7.0.41 - New Features — Output Options
- The Steel Design Effective Lengths output table now includes the subspan length and the effective length factor (Le/L).
- Steel Design Effective Length Factors, Major, Minor and LT may now be contoured per subspan.
GSA 8.7.0.41 - New Features — Graphic View — General
- In the Contour Settings dialog improvements have been made to the automatic setting of contour settings for special cases, e.g. when changing from 'governing utilisation' to 'overall utilisation' or from a utilisation to a non-special data option.
- When annotating contour barrels (i.e. on 1D and wall elements) stretches of constant value are now annotated with a single value at the centre of the stretch.
GSA 8.7.0.41 - New Features — Interface with Third Party Software
- GsRevit Export: The mappings database (mappings.db3) may now be edited directly in the Export to Oasys GSA dialog.
- GsRevit Export: The mapping priority may now be specified in the Export to Oasys GSA dialog.